Somewhat Urgent DriveShaft Question - Land Rovers Only

Street Wolf · 09-02-2008, 08:46 PM

I need to replace my front drive shaft really soon, however I have a Tom Woods shaft currently that was installed before I purchased the Disco, and I am also lifted.

I was wondering if a stock OEM front driveshaft can be bolted right back up in place?

Disco Mike · 09-03-2008, 07:33 AM

Why are you wanting to replace your current drive shaft, it is easily rebuildable?
Mike

mudmonkey · 09-03-2008, 11:14 AM

If you do decide to replace and not rebuild- call Tom Woods Shafts and they will have you measure the space between the flanges to allow for your additional lift. My shaft went South last week and the guy's at Tom Woods made me one up the following day to my spec and shipped overnight.

Street Wolf · 09-12-2008, 02:07 PM

I already had a Tom Woods shaft installed on the front and on the back. However when I sent my front drive shaft into them, they just called me back today and stated that it was so badly damaged that it's going to cost nearly as much to rebuild it as it would to just buy a new one.

So needless to say they're sending that one back along with a newer model shaft as well.

09-02-2008, 08:46 PM	#1 (permalink)
Street Wolf 3800 Tech Join Date: Apr 2008 Location: Wichita Falls, Texas Posts: 185 Gallery: 0	Somewhat Urgent DriveShaft Question I need to replace my front drive shaft really soon, however I have a Tom Woods shaft currently that was installed before I purchased the Disco, and I am also lifted. I was wondering if a stock OEM front driveshaft can be bolted right back up in place?

09-03-2008, 11:14 AM	#3 (permalink)
mudmonkey Senior Member Join Date: Nov 2007 Posts: 108 Gallery: 0	If you do decide to replace and not rebuild- call Tom Woods Shafts and they will have you measure the space between the flanges to allow for your additional lift. My shaft went South last week and the guy's at Tom Woods made me one up the following day to my spec and shipped overnight. __________________ D2 with stuff added

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Tie Rod End question	RageRover	Range Rover Classic	8	09-14-2008 11:33 PM
MAF sensor housing question	tcpfl	Discovery Series II	2	11-12-2007 05:49 PM
Driveshaft URGENT!!!	RageRover	Range Rover Classic	41	06-28-2006 04:08 PM
U-joint	roverX	Discovery Series I	2	03-22-2006 03:54 PM
One Question IQ Test	75series3	The Lounge	10	12-05-2005 11:09 PM

Remove Advertisements Sponsored Links
Land Rovers Only - Land Rover Forum Advertisement

09-03-2008, 07:33 AM	#2 (permalink)
Disco Mike Moderator Join Date: Aug 2004 Location: Parker, Colorado Posts: 5,785 Gallery: 0	Why are you wanting to replace your current drive shaft, it is easily rebuildable? Mike

09-12-2008, 02:07 PM	#4 (permalink)
Street Wolf 3800 Tech Join Date: Apr 2008 Location: Wichita Falls, Texas Posts: 185 Gallery: 0	I already had a Tom Woods shaft installed on the front and on the back. However when I sent my front drive shaft into them, they just called me back today and stated that it was so badly damaged that it's going to cost nearly as much to rebuild it as it would to just buy a new one. So needless to say they're sending that one back along with a newer model shaft as well.

Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)