Disco1 Remote Programming - Land Rovers Only

honybears · 10-08-2005, 04:50 AM

Hi Guys,
Does anyone have information on programming a 94 Disco1 Keyless remote?
Thanks.

Bongo · 10-08-2005, 07:15 AM

Hello,
Have you tried this web site http://www.remotekey.co.uk/Batteries.htm I used these instructions to reset the remote for my 300Tdi. If this does not work you can contact then and see what they say.
Hope this helps.

frickjp · 10-15-2005, 08:51 PM

HANDSET INITIALISATION
New handsets are supplied in pairs. If a new
handset is required, it will require initialisation to the
Theft Alarm Unit (Z163) using the following
procedure:
1. Starting conditions: ignition off, doors unlocked,
bonnet switch depressed.
2. Carry out instructions 3 to 9 within 8 seconds.
3. Switch ignition ON.
4. Switch ignition OFF.
5. Lock doors.
6. Unlock doors.
7. Release bonnet switch.
8. Switch ignition ON.
9. Switch ignition OFF.
If alarm is correctly accessed, horn will sound and
LED will light. It is now possible to programme two
handsets of correct frequency to vehicle alarm
ECU. This must be carried out within two minutes.
10. Press and hold down button on first handset
until dash LED flashes.
11. Repeat instruction 10. for second handset.
12. The LED will extinguish if both handsets have
been initialised correctly.

frickjp · 10-15-2005, 08:52 PM

Oh, and if you only have 1 handset just use the one twice.

asterix · 10-15-2005, 08:57 PM

Frickjp,

Does the procedure you supplied work for a 96 Disco?

honybears · 10-16-2005, 03:57 AM

Hey Guys,
Thanks for the info. I have ONE SINGLE button remote. Do I use the same instructions?

frickjp · 10-16-2005, 05:58 AM

2-button remotes have to be programmed with Testbook. This works on 1-button systems.

10-08-2005, 04:50 AM	#1 (permalink)
honybears Member Join Date: Sep 2005 Posts: 51 Gallery: 0	Disco1 Remote Programming Hi Guys, Does anyone have information on programming a 94 Disco1 Keyless remote? Thanks.

10-16-2005, 03:57 AM	#6 (permalink)
honybears Member Join Date: Sep 2005 Posts: 51 Gallery: 0	keyless remote Hey Guys, Thanks for the info. I have ONE SINGLE button remote. Do I use the same instructions?

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Remove Advertisements Sponsored Links
Land Rovers Only - Land Rover Forum Advertisement

10-08-2005, 07:15 AM	#2 (permalink)
Bongo Member Join Date: Sep 2005 Location: The garden of England Posts: 3 Gallery: 0	Hello, Have you tried this web site http://www.remotekey.co.uk/Batteries.htm I used these instructions to reset the remote for my 300Tdi. If this does not work you can contact then and see what they say. Hope this helps.

10-15-2005, 08:51 PM	#3 (permalink)
frickjp Senior Member Join Date: Dec 2004 Location: Buffalo, NY Posts: 128 Gallery: 0	HANDSET INITIALISATION New handsets are supplied in pairs. If a new handset is required, it will require initialisation to the Theft Alarm Unit (Z163) using the following procedure: 1. Starting conditions: ignition off, doors unlocked, bonnet switch depressed. 2. Carry out instructions 3 to 9 within 8 seconds. 3. Switch ignition ON. 4. Switch ignition OFF. 5. Lock doors. 6. Unlock doors. 7. Release bonnet switch. 8. Switch ignition ON. 9. Switch ignition OFF. If alarm is correctly accessed, horn will sound and LED will light. It is now possible to programme two handsets of correct frequency to vehicle alarm ECU. This must be carried out within two minutes. 10. Press and hold down button on first handset until dash LED flashes. 11. Repeat instruction 10. for second handset. 12. The LED will extinguish if both handsets have been initialised correctly.

10-15-2005, 08:52 PM	#4 (permalink)
frickjp Senior Member Join Date: Dec 2004 Location: Buffalo, NY Posts: 128 Gallery: 0	Oh, and if you only have 1 handset just use the one twice.

10-15-2005, 08:57 PM	#5 (permalink)
asterix Member Join Date: Oct 2005 Posts: 6 Gallery: 0	Frickjp, Does the procedure you supplied work for a 96 Disco?

10-16-2005, 05:58 AM	#7 (permalink)
frickjp Senior Member Join Date: Dec 2004 Location: Buffalo, NY Posts: 128 Gallery: 0	2-button remotes have to be programmed with Testbook. This works on 1-button systems.

Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)